雙螺條粉體混合機是根據國外技術開發的新產品，具有混合結構特殊、速度快、混合均勻等特點.與物料接觸部分均為不銹鋼制作，拋光處理，不粘料,螺條由內外兩層制成，內部螺條將物料推到端面,外部螺條將物料移到中心位置，兩者使物料高速輻射運動,達到迅速混合的目的。設備可帶冷熱夾套,電機可調速或防爆，材質可根據物料選擇,以滿足不同用戶的要求。
<track id="ualwx"></track>
<ol id="ualwx"></ol>
雙螺條粉體混合機是根據國外技術開發的新產品，具有混合結構特殊、速度快、混合均勻等特點.與物料接觸部分均為不銹鋼制作，拋光處理，不粘料,螺條由內外兩層制成，內部螺條將物料推到端面,外部螺條將物料移到中心位置，兩者使物料高速輻射運動,達到迅速混合的目的。設備可帶冷熱夾套,電機可調速或防爆，材質可根據物料選擇,以滿足不同用戶的要求。
Vacuum rake dryer major components of
1, shell 2, harrow teeth 3, a feeding device
4, unit 5, crushing rod 6, sealing device
7, stirring shaft 8, transmission
Vacuum rake dryer with a simple structure, easy operation, long life cycle, stable performance and reliable, steam consumption is small, applicability, product quality is good, especially for non-high temperature, flammable, easily oxidized at high temperature paste materials like dry, the aircraft long-term use by the users proved to be a good drying equipment.
Principle was dried material from the shell on the side is the middle in the ever-positive and negative rotation of the rake teeth stirring, the material axial walking back and forth, with the surface of the shell wall in contact constantly updated by indirect steam heating, uniform mixing rake teeth , smash smash rods, so that material inside the water evaporation, in a vacuum under the action of the system, so that internal moisture has been dried materials and surface water a more favorable discharge, vaporization of water through the dry-type dust collector, wet filter, condenser, vacuum pump exit from shorting.
Unserviceable stores:
| Slurry | Paste | Below 100 mesh material |
| A variety of pigments, soil-like material | Filtration | Centrifuge and filter |
| Soda ash detergent, alkali rock | Starch, dyes | Paints, clay |
| Gray etc. | Clay etc. | Cement etc. |
Be applied under the appropriate conditions:
| Below 100 mesh material | Solution |
| Synthetic fibers, crystalline | Vacuum liquid, emulsion |
| Gan Achillea films, minerals and | Suspension |
Model and technical parameters:
| The main parameters Model | Nominal Capacity (m3) | Heat transfer area(m2) | A loading (m3) | Absolute working pressure | Operating Temperature (K) | Spindle Speed(rpm) | Material | Weight (kg) | Power (KW) | Dimensions | |
| Cylinder diameter (MPa) | Jacket diameter(MPa) | ||||||||||
| XPG0.5 | 0.5 | 1.86 | 0.2 | 0.021 | 0.686 | 435 | 15-20 | Main:3 | |||
| Secondary:5.5 | |||||||||||
| XPG1 | 1 | 6 | 0.75 | 0.021 | 0.686 | 435 | 9 | A3 | 3400 | 5.5 | 3700 ×945 ×3270 |
| 1Cr18Ni9Ti | 3300 | ||||||||||
| XPG2 | 2 | 8 | 1.2 | 0.021 | 0.588 | 425 | 9 | A3 | 4900 | 11 | 4570 ×1130 ×3455 |
| 1Cr18Ni9Ti | 4800 | ||||||||||
| XPG3 | 3 | 11.5 | 1.8 | 1.021 | 0.588 | 425 | 9 | A3 | 6400 | 15 | 6076 ×1130 ×2980 |
| 1Cr18Ni9Ti | 6300 | ||||||||||
Technical Support：YOUWEI
<track id="ualwx"></track>
<ol id="ualwx"></ol>